What are three types of PVLAN broadcast domains? (Choose three.)
Two PCs are attached to a hub, which is attached to port ge-0/0/0 on your EX Series switch. You must separate the incoming traffic from the PCs into two VLANs.What should you use to accomplish this task?
-- Exhibit --Mar 16 17:54:51.930726 OSPF periodic xmit from 172.14.10.1 to 224.0.0.5 (IFL 69 area 0.0.0.0)Mar 16 17:54:55.566920 ospf_trigger_build_telink_lsas : No peer foundMar 16 17:54:56.152585 ospf_trigger_build_telink_lsas : No peer foundMar 16 17:54:56.152721 ospf_set_lsdb_statE. Router LSA 192.168.2.1 adv-rtr 192.168.2.1 state QUIET->GEN_PENDINGMar 16 17:54:56.153271 OSPF trigger router LSA 0x156d0f0 build for area 0.0.0.0 lsa-id 192.168.2.1Mar 16 17:54:56.157854 ospf_set_lsdb_statE. Router LSA 192.168.2.1 adv-rtr 192.168.2.1 state GEN_PENDING->QUIETMar 16 17:54:56.157971 OSPF built router LSA, area 0.0.0.0, link count 2Mar 16 17:54:56.158300 OSPF sent Hello 172.14.10.1 -> 224.0.0.5 (ge-0/0/1.0 IFL 69 area 0.0.0.0)Mar 16 17:54:56.158380 Version 2, length 44, ID 192.168.2.1, area 0.0.0.0Mar 16 17:54:56.158435 mask 255.255.255.0, hello_ivl 10, opts 0x2, prio 128Mar 16 17:54:56.158485 dead_ivl 40, DR 172.14.10.1, BDR 0.0.0.0Mar 16 17:54:56.158949 OSPF DR is 192.168.2.1, BDR is 0.0.0.0Mar 16 17:54:56.159276 OSPF sent Hello 172.14.10.1 -> 224.0.0.5 (ge-0/0/1.0 IFL 69 area 0.0.0.0)Mar 16 17:54:56.159331 Version 2, length 44, ID 192.168.2.1, area 0.0.0.0Mar 16 17:54:56.159401 mask 255.255.255.0, hello_ivl 10, opts 0x2, prio 128Mar 16 17:54:56.159563 dead_ivl 40, DR 172.14.10.1, BDR 0.0.0.0Mar 16 17:54:56.168108 OSPF DR is 192.168.2.1, BDR is 0.0.0.0Mar 16 17:54:58.237416 OSPF rcvd Hello 172.14.10.2 -> 224.0.0.5 (ge-0/0/1.0 IFL 69 area 0.0.0.0)Mar 16 17:54:58.237540 Version 2, length 44, ID 192.168.2.1, area 0.0.0.0Mar 16 17:54:58.237623 checksum 0x0, authtype 0Mar 16 17:54:58.237698 mask 255.255.255.0, hello_ivl 10, opts 0x2, prio 128Mar 16 17:54:58.237751 dead_ivl 40, DR 172.14.10.2, BDR 0.0.0.0-- Exhibit --Click the Exhibit button.Looking at the traceoptions output in the exhibit, why are the OSPF routers stuck in Init state?
-- Exhibit --{master:0}[edit]user@switch# show vlansv1 {vlan-id 1;interface {ge-0/0/1.0;}}v2 {vlan-id 2;interface {ge-0/0/2.0;}}v3 {vlan-id 3;interface {ge-0/0/1.0 {}{master:0}[edit]user@switch# show interfaces ge-0/0/3unit 0 {family ethernet-switching {port-mode trunk;}}{master:0}[edit]user@switch# run show vlansName Tag InterfacesdefaultNone -v1 1ge-0/0/1.0*, ge-0/0/3.0*v2 2ge-0/0/2.0*, ge-0/0/3.0*v3 3ge-0/0/1.0*, ge-0/0/3.0*-- Exhibit --Click the Exhibit button.Referring to the exhibit, what would explain interface ge-0/0/3.0 being active in VLANs v1, v2, and v3?
You are asked to implement a filter-based VLAN assignment. You have created the firewall filter and must apply this filter to the incoming interface.Where must this filter be applied?
Which connection method do OSPF routers use to communicate with each other?
