Which two statements are associated with any-source multicast? (Choose two.)
In a carrier-of-carrier VPN model, which type of network layer reachability information is used for the MP-BGP signaling between CE and PE routers?
To reduce the size of OSPF Area 100, you configure the area with the no-summaries parameter. After committing this configuration change, you notice that anOSPF router in a remote area is no longer receiving Type 5 LSAs from an ASBR in Area 100.Which statement is true in this scenario?
Click the Exhibit button.Referring to the exhibit, you control AS 24652. You are asked to ensure that traffic destined to the 23.56.83.0/24 network from ISP 4 takes the most optimum path through ISP 3. ISP 1 should be used as a backup for this traffic flow.Which two actions would accomplish this task? (Choose two.)
An L2VPN (draft-kompella-mpls-l2vpn) is established between two PE routers to provide connectivity between two customer sites.Which two statements related to this deployment are true? (Choose two.)
Click the Exhibit button.[edit]user@PE-1# run show l2 circuit connectionsLayer-2 Circuit Connections:Legend for connection status (St)EI - - encapsulation invalid NP - - interface h/w not presentMM - - mtu mismatch Dn - - downEM - - encapsulation mismatch VC-Dn - -Virtual circuit Down -CM - - control-word mismatch Up - -operationalVM - - vlan id mismatch CF - - Calladmission control failureOL - - no outgoing label IB - - TDMincompatible bitrareNC - - intf encaps not CCC/TCC TM - - TDMmisconfigurationBK - - Backup Connection ST - - StandbyConnection -CB - - rcvd cell-bundle size bad SP - - StaticPseudowire -LD - - local site signaled down RS - - remotesite standbyRD - - remote site signaled down XX - - unknownLegend for interface status -Up - - operational -Dn - - down -Neighbor: 4.4.4.4 -Interface Type St Timelast up #Up transge-0/0/1.512 (vc 1) rmt OL[edit]user@PE-1# show protocols ldpinterface ge-0/0/2.0;[edit]user@PE-1# show protocols l2circuitneighbor 4.4.4.4 {interface ge-0/0/1.512 {virtual-circuit-id 1}}[edit]user@PE-1# show interfaces ge-0/0/1vlan-tagging;encapsulation vlan-ccc;unit 512 {encapsulation vlan-ccc;vlan-id 512;}[edit]uxer@P-1 # show protocols ldpinterface all;[edit]user@P-2# show protocols ldpinterface all;[edit]user@PE-2# run show l2circuit connectionsLayer-2 Circuit Connections:Legend For connection status (St)EI - - encapsulation invalid NP - - interface h/w not presentMM - - mtu mismatch Dn - - downEM - - encapsulation mismatch VC-Dn - -Virtual circuit Down -CM - - control-word mismatch Up - -operationalVM - - vlan id mismatch CF - - Calladmission control failureOL - - no outgoing label IB - - TDMincompatible bitrateNC - - intf encaps not CCC/TCC TM - - TDMmisconfigurationBK - - Backup Connection ST - - StandbyConnection -CB - - rcvd cell-bundle size bad SP - - StaticPsewdowire -LD - - Local site signaled down RS - - remotesite standbyRD - - remote site signaled down XX - - unknownLegend for interface status -UP - - operational -DN - - down -Neighbor: 1.1.1.1 -Interface Type St Timelast up #Up transge-0/0/1.512 (vc 1) rmt OL[edit]user@PE-2# show protocols ldpinterface ge-0/0/2.0;[edit]user@PE-2# show protocols l2circuitneighbor 1.1.1.1 {interface ge-0/0/1.512 {virtual-circuit-id 1;}}[edit]user@PE-2# show interfaces ge-0/0/1vlan-tagging;encapsulation vlan-ccc;unit 512 {encapsulation vlan-ccc;vlan-id 512;}Referring to the exhibit, you have configured an L2 circuit that connects Site-1 and Site-2, but the L2 circuit is not functioning. The topology in this scenario is shown below.Site-1 > PE-1 > P-1 > P-2 > PE-2 Site-2Which action will allow communication between Site-1 and Site-2?
