What is a benefit of MACsec in a multilayered LAN network design?
SIMULATION-Guidelines-This is a lab item in which tasks will be performed on virtual devices.• Refer to the Tasks tab to view the tasks for this lab item.• Refer to the Topology tab to access the device console(s) and perform the tasks.• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.• All necessary preconfigurations have been applied.• Do not change the enable password or hostname for any device.• Save your configurations to NVRAM before moving to the next item.• Click Next at the bottom of the screen to submit this lab and move to the next question.• When Next is clicked, the lab closes and cannot be reopened.Topology-Tasks-OSPF is preconfigured on all devices except R20. Configure R20 to complete these tasks.Task 1:Configure OSPF according to the topology using these requirements:• Use Process ID 20.• Use Loopback0 for the Router ID.• Advertise all networks into OSPF.o Do not use network statements under the OSPF process to accomplish this task.Task 2:Configure a /18 summary route for Area 40.• Advertise only Type 3 LSAs into Area 0.R20-
Which function is performed by vSmart in the Cisco SD-WAN architecture?
SIMULATION-Guidelines-This is a lab item in which tasks will be performed on virtual devices.• Refer to the Tasks tab to view the tasks for this lab item.• Refer to the Topology tab to access the device console(s) and perform the tasks.• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.• All necessary preconfigurations have been applied.• Do not change the enable password or hostname for any device.• Save your configurations to NVRAM before moving to the next item.• Click Next at the bottom of the screen to submit this lab and move to the next question.• When Next is clicked, the lab closes and cannot be reopened.Topology-Tasks-OSPF is partially configured on all devices. Complete the configurations to achieve these results:1. Configure R3 so that R20 is always designated as the BDR.2. Configure R10 so that it does not participate in the DR/BDR election. Do not use the ip ospf network point-to-point command under the interface configuration to accomplish this task.
SIMULATION-Guidelines-This is a lab item in which tasks will be performed on virtual devices.• Refer to the Tasks tab to view the tasks for this lab item.• Refer to the Topology tab to access the device console(s) and perform the tasks.• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.• All necessary preconfigurations have been applied.• Do no remove any existing configurations from the devices, only those necessary to make the appropriate changes required to fulfill the listed tasks.• Do not change the enable password or hostname for any device.• Save your configurations to NVRAM before moving to the next item.• Click Next at the bottom of the screen to submit this lab and move to the next question• When Next is clicked, the lab closes and cannot be reopened.Topology-Tasks-The Operations team started configuring several monitoring activities. Complete the configurations for the tasks below.1. Enable Flexible NetFlow on R1 E0/0 in both directions using the pre-configured flow monitor.2. Configure the switch port analyzer on Sw1 and mirror all VLAN 12 traffic to interface E1/3 using session number 12.3. Configure a basic IP SLA ICMP echo operation on R1 to ping PC1 every 300 seconds.R1-
SIMULATION-Guidelines-This is a lab item in which tasks will be performed on virtual devices.• Refer to the Tasks tab to view the tasks for this lab item.• Refer to the Topology tab to access the device console(s) and perform the tasks.• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.• All necessary pre-configurations have been applied.• Do not remove any existing configurations from the devices, only those necessary to make the appropriate changes required to fulfill the listed tasks.• Do not change the enable password or hostname for any device.• Save your configurations to NVRAM before moving to the next item.• Click Next at the bottom of the screen to submit this lab and move to the next question.• When Next is clicked, the lab closes and cannot be reopened.Topology-Tasks-Configure R1 according to the topology to achieve these results:1. Configure eBGP using Loopback 0 for the router-id. Do not use the address-family command to accomplish this.2. Advertise R1’s Loopback 100 and Loopback 200 networks to AS20 and AS30.
