An engineer must update the local web authentication details on a Cisco 5520 WLC. The engineer has one active SSID configured for web authentication and plans to update the virtual interface with a nonroutable IP address. Which command must the engineer apply?
SIMULATION-Guidelines-This is a lab item in which tasks will be performed on virtual devices.• Refer to the Tasks tab to view the tasks for this lab item.• Refer to the Topology tab to access the device console(s) and perform the tasks.• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.• All necessary preconfigurations have been applied.• Do not change the enable password or hostname for any device.• Save your configurations to NVRAM before moving to the next item.• Click Next at the bottom of the screen to submit this lab and move to the next question.• When Next is clicked, the lab closes and cannot be reopened.Topology-Tasks-OSPF is preconfigured on all devices except R20. Configure R20 to complete these tasks.Task 1:Configure OSPF according to the topology using these requirements:• Use Process ID 10.• Use Loopback1 for the Router ID.• Advertise all networks into OSPF.o Use network statements under the OSPF process to accomplish this task.Task 2:Configure a /20 summary route for Area 40.• Advertise only Type 3 LSAs into Area 0.R20-
SIMULATION-Guidelines-This is a lab item in which tasks will be performed on virtual devices.• Refer to the Tasks tab to view the tasks for this lab item.• Refer to the Topology tab to access the device console(s) and perform the tasks.• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.• All necessary preconfigurations have been applied.• Do not change the enable password or hostname for any device.• Save your configurations to NVRAM before moving to the next item.• Click Next at the bottom of the screen to submit this lab and move to the next question.• When Next is clicked, the lab closes and cannot be reopened.Topology-Tasks-The operations team started configuring network devices for a new site. Complete the configurations to achieve these goals:1. Configure Rapid PVST+ on SW20.2. The trunk between SW20 and SW30 is not operational. Troubleshoot the issue and ensure PC3 can ping PC1 (10.10.100.10) across the link.3. The LACP port channel between SW10 and SW20 is not operational. Troubleshoot the issue and ensure PC3 can ping PC2 (10.10.100.20) across the port channel.Note: No access is provided to SW10 or SW30. Resolve these issues by making changes only to SW20. Traffic on all trunks should be restricted to only active VLANs.
SIMULATION-Guidelines-This is a lab item in which tasks will be performed on virtual devices.• Refer to the Tasks tab to view the tasks for this lab item.• Refer to the Topology tab to access the device console(s) and perform the tasks.• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.• All necessary pre-configurations have been applied.• Do not change the enable password or hostname for any device.• Save your configurations to NVRAM before moving to the next item.• Click Next at the bottom of the screen to submit this lab and move to the next question.• When Next is clicked, the lab closes and cannot be reopened.Topology-Tasks-EIGRP is preconfigured on all routers. Configure R10 and R20 to complete these tasks.Task 1:Modify the existing ACL on R10 so that EIGRP routes are received from R20 and R30.• The modification should only allow EIGRP routes to pass.• Do not remove any configuration from R10 to achieve this task.Task 2:Configure CoPP on R20 to achieve these results:• Permit ICMP traffic from 192.168.24.0/24.• Limit traffic to 8,000 bps.• Discard additional packets.
SIMULATION-Guidelines-This is a lab item in which tasks will be performed on virtual devices.• Refer to the Tasks tab to view the tasks for this lab item.• Refer to the Topology tab to access the device console(s) and perform the tasks.• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.• All necessary preconfigurations have been applied.• Do no remove any existing configurations from the devices, only those necessary to make the appropriate changes required to fulfill the listed tasks.• Do not change the enable password or hostname for any device.• Save your configurations to NVRAM before moving to the next item.• Click Next at the bottom of the screen to submit this lab and move to the next question• When Next is clicked, the lab closes and cannot be reopened.Topology-Tasks-OSPF is partially configured. Complete the OSPF configurations to achieve these goals:1. Configure OSPF on router R1 according to the topology so that all networks are advertised. Do not use the network statement under the “router ospf” configuration section to accomplish this task.2. Configure a single command on the ABR routers to ensure only one summary route is advertised to area 0.R1-
SIMULATION-Guidelines-This is a lab item in which tasks will be performed on virtual devices.• Refer to the Tasks tab to view the tasks for this lab item.• Refer to the Topology tab to access the device console(s) and perform the tasks.• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.• All necessary preconfigurations have been applied.• Do not change the enable password or hostname for any device.• Save your configurations to NVRAM before moving to the next item.• Click Next at the bottom of the screen to submit this lab and move to the next question.• When Next is clicked, the lab closes and cannot be reopened.Topology-Tasks-The operations team started configuring network devices for a new site. R10 and R20 are preconfigured with the CORP VRF. R10 has network connectivity to R20. Complete the configurations to achieve these goals:1. Extend the CORP VRF between R10 and R20 using Tunnel0.2. Protect Tunnel0 using the preconfigured profile.
